Kahant Electrical Supply Co.

Laser Scanner

Laser Scanner

OS32 Laser Scanner

The Omron OS32 Laser Scanner is very easy to configure with its amazing software, you can have it up and running in less that 30 minutes.The software allows you to configure custome safety ares, and also warning zones with drag and drop fields. If the scanner ever needs to be replaced you do not have to reconfigure the parameters in it, just replace the scanner head and turn it on thus saving down time on your machine.

Laser Details

OS32C Laser Scanner Specifications

• Sensor Type: Type 3
• Safety Laser Scanner Safety Category: Category 3, Performance Level d (ISO13849-1: 2006)
• Detection Capability Non-Transparent With a Diameter Of 70 mm (1.8% Reflectivity Or Greater)
• Monitoring Zone Monitoring Zone Set Count: (Safety Zone + 2 Warning Zones) x 70 Sets
• Operating Range Safety Zone Radius Up To 3 m; Warning Zone Radius Up To 10 m
• Maximum Measurement Error 100 mm *1
• Detection Angle 270 Degrees
• Angular Resolution 0.4 Degrees
• Laser Beam Diameter 6 mm At Optics Cover, 14 mm At 3 m
• Response Time Response Time From ON To OFF: From 80 ms (2 scans) To 680 ms (Up To 17 scans)
• Response Time From OFF to ON: Response Time From ON to OFF + 100 ms to 60s (Configurable)
• Zone Switching Time 20 To 320 ms
• Line Voltage 24 VDC +25%/-30% (Ripple p-p 2.5 V max.)
• *2 Power Consumption Normal Operation: 5 W max., 4 W Typical (Without Output Load)
• *3 Standby Mode: 3.75 W (Without Output Load)
• Emission Source (Wavelength) Infrared Laser Diode (905 nm)
• Laser Protection Class:
• Class 1: IEC/EN60825-1 (2007)
• Class 1: JIS6802 (2005)
• Class I: CFR21 1040.10, 1040.11
• Safety Output (OSSD): PNP Transistor x 2, Load Current Of 250ma Max., Residual Voltage Of 2 V Max.
• Load Capacity Of 2.2 Degrees F Max., Leak Current Of 1 Ma Max. *3, *4, *5
• Auxiliary Output (Non-Safety): NPN/PNP Transistor X 1, Load Current Of 100 Ma Max., Residual Voltage Of 2 V Max., Leak Current Of 1 Ma Max. *4, *5, *7
• Warning Output (Non-Safety): NPN/PNP Transistor X 1, Load Current Of 100 Ma Max., Residual Voltage Of 2 V Max., Leak Current Of 1 Ma Max. *4, *5, *7
• Output Operation Mode: Auto Start, Start Interlock
• Start/Restart Interlock
• Input
• External Device
• Monitoring (EDM)
• ON: 0 V Short (Input Current Of 50 ma)
• OFF: Open Start ON: 0 V Short (Input Current Of 20 ma)
• OFF: Open Zone Select ON: 24 V Short (Input Current Of 5 ma)
• OFF: Open Stand-By ON: 24 V Short (Input Current Of 5 ma)
• OFF: Open
• Connection Type Power Cable: 18-Pin Mini-Connector (Pigtail)
• Communication Cable: M12, 4-Pin Connector
• Connection With PC *6
• Communications: Ethernet
• OS Supported: Windows 2000, Windows XP, Or Windows Vista
• Indicators RUN Indicator: Green, STOP Indicator: Red, Interlock Indicator: Yellow, Warning Output Indicator: Orange
• Status/Diagnostic Display: 2 X 7-Segment LEDs
• Intrusion Indicators: Red LED X 8 Protective Circuit Protection Against Output Load Short and Reverse Power Connection
• Ambient Temperature Operation: -10 To 50 Degrees C
• Storage: -25 To 70 Degrees C Ambient Humidity Operation & Storage: 95% RH Max.
• Non-Condensing Ambient Operation Illumination Incandescent Lamp: Illumination On Receiving Surface 1500 Lx Max. (An Angle Of Laser Scanning Plane and Disturbance; Light Must Be 5 Degrees Or More) Enclosure Rating IP65 (IEC60529)
• Enclosure Sensor Head: Die-Cast Aluminum
• Optical Cover: Polycarbonate
• I/O Block: Die-Cast Aluminum Dimensions (Wxhxd) 133.0 x 104.5 x 142.7 mm (Except Cable)
• Dielectric Withstand Voltage 350 VAC, 50/60 hz, 1-Minute
• Insulation Resistance 20 Mega-Ohm Or Higher (500 VDC)
• Impact Resistance 98 M/S2 1,000 Times for Each Of X, Y, and Z Directions (IEC 60068-2-29)
• Vibration 10 To 55 Hz Double-Amplitude Of 0.7 mm, 20 Sweepings For X, Y, and Z Directions (IEC60068- 2-6)
• Weight (Main Unit Only): 1.3 kg
• Power Cable Up To 30m
• Communication Cable Up To 100 m for 100 BASE-T Cat 5 Cable
• Accessories CD-ROM (User's Manual and Configuration Tool)
• Approvals EN61496-1 (Type 3 ESPE), EN61496-3 (Type 3 AOPDDR), EN61508 (SIL2), IEC61496-1 (Type 3 ESPE), IEC61496-3 (Type 3 AOPDDR), IEC61508 (SIL2), UL508, UL1998, CAN/CSA-C22.2 No. 14, -CAN/CSA-C22.2 No. 0.8